$130.00
Description
| Feature | Description |
|---|---|
| 🔥 Profiles | Create custom heater profiles for different heaters and operating preferences. |
| ⏰ Schedules | Automate your heater with daily schedules. Configure ON, OFF, and Target Temperature actions for selected days and times. |
| 📡 RF Remote Support | Pair new or existing RF remotes using the onboard CC1101 transceiver. |
| 🌡️ Multi-Room Temperature Sensors | Add additional temperature sensors via the I²C or 1-Wire bus for multi-room monitoring. |
| 🌐 Network Connectivity | Connect to your existing Wi-Fi network or configure the controller in standalone Access Point AP mode. |
| 🔄 OTA Updates | Update firmware over the internet, via the local network, or by manually uploading a firmware file. |
| 🖥️ Optional Remote Touchscreen | Add a 2.8-inch Wi-Fi touchscreen for convenient remote control. Includes a built-in BME280 sensor for cabin temperature and humidity monitoring. |
| 🔌 Plug & Play Installation | Fully open-source hardware designed for simple, plug-and-play installation. |
| 🏠 Home Assistant & ESPHome | Native integration with Home Assistant using ESPHome for seamless automation and monitoring. |
| 📱 Mobile-Friendly Interface | Fully responsive web interface designed for mobiles, tablets and desktops, making control and management easy from anywhere. |
| 🔌 Auto Tune | One click auto tune setup. Runs through a series of presets until successful ignition is detected and saves a new profile. |
**Available for Preorder now
The WebUI is fully responsive and mobile friendly and offers full visibility of the heaters CORE temperature. This allows for much finer tuning and control. Additionally it offers schedules, heater profiles and multiple sensors. A full list of features can be found below.
Decimal Accuracy Core Temperature
Allows monitoring the heaters core temperature down to .1 of a degree. This allows for easier tuning, finer tuning and better startup monitoring. During startup, you should instantly see the core temperature rise to indicate a successful start. Tuning guides can be found in the documentation.
Temperature can be configured in Calculus and Fahrenheit.
Auto Tune
Auto tune will run through a list of default settings until a successful ignition is detected and save these setting in a new Profile. This makes it easy to find the correct Fan Speed, Pump Rate and Glow times for your heater. Fine tuning to the profile can then be done from this newly created profile giving a solid base profile to work from.
Heater Schedules
Set schedules to start and stop the heater. Schedules are flexible and different target temperatures can be set for different schedules. Selectable by day(s) of the week, with start and end times.
Heater Profiles
Heater profiles allows for specific heater profiles, or even for testing. Profiles are used to set heater specific settings such as Prime Rate, Max Heater Core Temp, Cool Down times etc. Heater profiles come in handy for testing, or change the controller between different heaters. By default the heater ships with 5 default heater profiles pre-configured.
User Control
Password protected UI allows for restricted access as well as additional users with specific permissions for control only, adding or removing schedules etc. Fully restrict each user down to permissions that only allow basic control functions such as start and stop.
Real Time Current and Voltage Monitoring
The built in INA129 and high current SHUNT allow for high current and accurate voltage measurement. This makes troubleshooting startup issues due to power drops easy and quick.
1Wire, I2C and UART Breakouts
The 1Wire and I2C breakouts allow for adding additional sensors. Additional temperature sensors can be added for better temperature accuracy. The board also include a UART breakout which could also be used for flashing if the USB port becomes unavailable.
Please note that an external temperature sensor is required if not using the Remote LCD Display.
OTA Updates
The system supports a wide range of update methods. These include Wi-Fi OTA, Manually Binary Upload or OTA via the internet.
ESPHome Support
Full supported for ESPhome and Home assistant. ESPhome configuration can be downloaded from the resources section.
Programmable GPIO
The on board programmable GPIOs allow for flexible control and monitoring. These can be configured as Inputs or Outputs and can be configured as INPUT_PULLUP or INPUT_PULLDOWN. A total of 4 on board IOs exist. Functions include
- Power ON / Power OFF
- Running / Cooling
- Fault
- Wi-Fi Connected / Disconnected
- Pump ON
- Glow ON
- Fan ON
- And more
Event Logging
The log output logs all events from network, user access to the heater faults and RF. This makes reviewing the logs and troubleshooting easy.
Screenshots of the WebUI and Mobile view.
On-Board Temperature and Humidity Sensor
The on board SHT3x offers a real time indication of the device temperature and humidity.
1Wire, I2C and UART breakouts
Add additional temperature sensors using either I2C or 1Wire using the breakouts shown below. An on board programmable UART is also available.
Configurable I/O
The IO breakouts allow for Input and Output functions. These are programmable from the WebUI and can be set for events such as Power ON, Power OFF, Over temp, Fault etc. A total of 4 GPIO pins are available and can be set all Input or Output mode, PULLUP or PULLDOWN.
Selectable Thermistor Resistance & RF Support via CC1101 Transceiver
Support a wide range of heaters with the selectable thermistor resistor value. The on board CC1101 transceiver allows for RF control for Power ON, Power OFF, Temperature UP and Temperature DOWN
High Current Rated up 20A with built-in Voltage and Current Monitoring
Additional information
| Options | Controller Only, Add CC1101, Add LCD Screen, Add Enclosure, Add CC1101 + LCD Screen, Add CC1101 + Enclosure, Add LCD Screen + Enclosure, Full Package |
|---|
Related products
-
Bindicator
$40.00 Select options This product has multiple variants. The options may be chosen on the product page -
Car-GPS LTE PCB
Read more
Reviews
There are no reviews yet